EnglishEspañolFrançaisDeutschPortuguês日本語한국인
最近のご注文
FC equip to SC Multimode OM3/OM4 Mode Conditioning Patch Cable

Press Esc key to close this popup
  • FC equip to SC Multimode OM3/OM4 Mode Conditioning Patch Cable

FC equip to SC Multimode OM3/OM4 Mode Conditioning Patch Cable

製品アイテム: #7628
P/N: MC-FCE-SC-10G
ベース価格: US$8.67

選択して下さい:






Order Today, Ship before 04/03/2024, from U.S. or HK
  • 説明
  • データシート
  • 商品タグ

FM SKU#:SKU00109JR
Model#:MC-FCE-SC-10G
MFG PART#:

FC equip to SC Multimode OM3/OM4 50/125 Mode Conditioning Patch Cable

Fiber-Mart manufactures and supplies standard and custom length 50/125, 62.5/125 and OEM equivalent mode conditioning fiber optic patch cords for 1000BASE-LX/LH Gigabit Ethernet (1300nm long wavelength) applications installed into existing multimode cable plants. These specialized cords help avoid Differential Mode Delay (DMD) effects that can occur when long wave transceiver modules operate at both single-mode and multimode wavelengths. And they are available with FC,ST, SC, LC and MT-RJ connectors.

How the Mode Conditioning Cable Works
The need for this conditioning fiber optic patch cord is due to the single-mode launch nature of the -LX or long-wave (1300nm) transceiver modules used for Gigabit Ethernet. Launching a single-mode laser into the center of a multimode fiber can cause multiple signals to be generated that confuse the receiver at the other end of the fiber. In that case, a mode conditioning patch cord eliminates these multiple signals by allowing the single-mode launch to be offset away from the center of a multimode fiber. This offset point creates a launch that is similar to typical multimode LED launches. (see diagram below)



Notes:

  • If some customers remain reluctant to deploy MCP cables, and for customers using OM3 or OM4 cables, please measure the power level before plugging the fiber into the adjacent receiver. When the received power is measured above -3dBm (in 1000BASE-LX links), a 5-dB attenuator for 1300nm should be used and plugged at the transmitter source of the optical module on each side of the link. Actually, OM3/OM4 MCP can also work in this event. While whether all multimode fiber types require mode conditioning, you can contact the manufacturer of your installed cable for the answer.
  • Mode conditioning patch cords can only convert single-mode to multimode. If you want to convert multimode to single-mode, then a media converter will be required.
  • Another alternative for short reaches within the same location is to use a single-mode patch cable. There will be no saturation over single-mode fiber.


  • How to Install the Mode Conditioning Cable
    If your gigabit LX switch is equipped with SC or LC connectors, please be sure to connect the yellow leg (Singlemode) of the cable to the transmit side, and the orange leg (multimode) to the receive side of the equipment. It is imperative that this configuration be maintained on both ends. The swap of transmit and receive can only be done at the cable plant side. (see diagram below)



Things to Know When Using Mode Conditioning Cables


  • Mode conditioning patch cords are usually used in pairs. Which means that you will need a mode conditioning patch cord at each end to connect the equipment to the cable plant.
  • Generally, Mode Conditioning patch cords are required for link distances greater than 984 feet (300 meters).




Features

  • Increased transmission bandwidth up to 4 times
  • Fits existing cabling scheme
  • Easy installation
  • Removes effects form DMD
  • Permanent, low-profile offset closure
  • Enables 1000Base-LX/LH optics to be used with Multi-Mode Fibre
  • PC, UPC, APC polish types
  • Low insertion loss (<1dB)
  • Reduced modal noise
  • Vcsel laser source into standard multimode fiber
  • OFNR rated jacket complies with strict building codes
  • Compliant with IEEE 802.3 applications

Application

  • Gigabit Ethernet
  • Equipment interconnection
  • High speed data transfer
  • LAN
  • Telecom network


  • MAKE TO ORDER Customizing your Mode Conditioning Cable (options)
Cable Jacket Fiber Type Connetcors length
  • • LSZH
  • • Custom
  • • Multimode 10G (OM3/OM4)
  • • Multimode 62.5/125
  • • Multimode 50/125
First End
  • • LC Equipment
  • • SC Equipment
  • • ST Equipment
  • • FC Equipment
  • • MTRJ Equipment
Second End
  • • LC
  • • SC
  • • ST
  • • FC
  • • MTRJ
  • • 1 m
  • • 2 m
  • • 3 m
  • • 5 m
  • • 10 m
  • • 15 m
  • • 20 m
  • • 25 m
  • • 30 m
  • • Custom

For assistance customizing your Mode Conditioning Cable, please call us at +1-205-282-9089 or email to [email protected].

 

InsertionLoss(dB) Non-ConditionedChannel(Multimode)
LC SC ST MTRJ
<0.5(max) <0.5(max) <0.5(max) <0.5(max)
ConditionedChannel(MultimodeDirection)
LC SC ST MTRJ
<1.0 <1.0 <1.0 <1.0
ConditionedChannel(Single-modeDirection)
LC SC ST MTRJ
>2.0;<22.0 >2.0;<22.0 >2.0;<22.0 >2.0;<22.0
FerruleMaterial Ceramic Ceramic Ceramic Thermoplastic
HousingMaterial Composite Composite Metal Composite


Datasheet to Download

Add your Tags



あなたの意見を教えてください、あなたの意見を他の人と分かち合いましょう。 コメントは製品に集中してください。



Copyright © 2024 Fiber-MART.COM. All Rights Reserved. Privacy Notice. Terms of Service
Fibermart ISO9001Fibermart Secure Certificate
商品タグ: A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z | 0-9
Email us