Wednesday 09 January, 2019 |
How Fiber Optic Cables Work & How Engineers Use Them To Send Messages
first, let me show you how fiber optic cables work.
I have a bucket that I modified with a window in front and on the other side, I put a stopper in this hole right here. I have a bottle of propylene glycol, with just a little bit of creamer in it. A ring stand and of course a laser pointer. Now, keep your eye on this plug when I turn out the lights.
That’s wonderful. The light follows the liquid flow all the way to the bucket. Amazing. It does this because of total internal reflection. As the light enters the stream, it is reflected as soon as it hits the interface between here and liquid.
You can see here the first reflection and then the second and the third. This occurs because there’s a difference between the index refraction of the guide material, here propylene glycol, and the outside air in this case. Recall that anytime light strikes a surface, it can either be absorbed by the material, reflected from it or passed into and through it, the latter we call “refraction”.
It’s easier to see from a top view. Reflection and refraction could happen at the same time. But if a light ray hits the surface at an angle greater than the critical angle, it will be completely reflected and not refracted.
For this propylene glycol and air system, as long as a beam hits the surface at an angle greater than 44.35 degrees, measured from the normal, it will propagate down the stream via total internal reflection. To create the same effect in an optical fiber, engineers create a core of glass, usually pure silicon dioxide and an outside layer called “cladding,” which they also typically make from silicon dioxide but with bits of boron or germanium to decrease its index of refraction.
A one percent difference is enough to make fiber optic cables work. To make such a long, thin piece of glass, engineers heat a large glass preform. Its center is the pure core glass and the outside the cladding. They then draw or pull a fiber by winding the melt on to a wheel at speeds up to 1600 meters per second. Typically these drawing towers are several stories tall. The height allows the fiber to cool before being wound onto a drum.
One of the greatest engineering achievements was the first ocean spanning fiber optic cable called TAT-8. It extended from Tuckerton, New Jersey, following the ocean floor over 3500 miles until branching out to Widemouth, England and Penmarch, France.
Engineers designed the cable carefully to survive on the ocean floor. At its center lies the core. Less than a tenth of an inch in diameter, it contains six optical fibers wrapped around a central steel wire. They embedded this in an elastomer to cushion the fibers, surround it with steel strands and then sealed it inside a copper cylinder to protect it from water. The final cable was less than an inch in diameter, yet it could handle some 40,000 simultaneous phone calls.
The essence of how they send information through a fiber optic cable is very simple. I could have a pre-arranged signal with someone at the other end. Perhaps we will use Morse code and I just block the laser, so that the person at that end sees flashes that communicate a message.
To transmit an analog signal, like voice from a phone call along the cable, engineers use Pulse Code Modulation. We take an analog signal and cut it up into sections and then approximate the wave’s loudness or amplitude as best we can.
We want to make this a digital signal, which means discrete values of loudness and not just any value. For example, I will use four bits, which means I have 16 possible values for the loudness. So the first four sections of the signal could be approximated by about 10, 12, 14 and 15.
We then take each section and convert its amplitude to a series of ones and zeros. The first bar of value 10, when encoded, becomes one, zero, one, zero. We can do this for each section of the curve.
Now instead of looking at the green wave form or even the blue bars, we can think of the signal as a series of ones and zeros organized by time. It is that sequence that we send through a fiber optic cable of flash for one and nothing for a zero. Now of course, the exact method of encoding is known at the receiving end. So it is a trivial matter to decipher the message.
Now you may be wondering how a laser pulse can travel nearly 4000 miles across the ocean. It doesn’t without some help because the light will escape from the sides of the fibers. Look back at our propylene stream.
Here’s how the light attenuates as it travels. You can see here a narrow beam in the bucket that broadens a bit when it enters the stream and then after the first bounce, the beam leaves even broader than it entered. That’s because the interface with the air is uneven and the rays that make up the beam strike at slightly different angles.
When that beam makes its second reflection, those individual rays diverge even more. Until by the time it reaches the third bounce, many of the rays are no longer at the critical angle and can exit from the sides of the stream. Here it happens in a few inches but in fiber optic cables like TAT-8, the signal travels a stunning 50 kilometers before it needs to be amplified. Absolutely amazing.
Other news for Wednesday 09 January, 2019
View all news for Wednesday 09 January, 2019 on one page
News for Tuesday 08 January, 2019
View all news for Tuesday 08 January, 2019 on one page
News Archive - See All News from Fiber-Mart.COM