EnglishEspañolFrançaisDeutschPусскийPortuguês日本語

fibermart-news_banner_9.jpg

 

Thursday 19 March, 2015 | RSS Feed

Optical Circulator Introduction

by www.fiber-mart.com

 
passive optical component fibermart

 

Optical Circulator

Optical Circulator, Fiber Circulator

Fiber optic communication has brought us a new Internet society. To better support an optical network, a variety of optical components and related technologies are neede. They have contributed to the evolution of optical communication, while improving the functionalities, reliability, and economical efficiency of optical networks. Passive optical components are the foundation stone of optical network systems, and circulator is one of them. This tutorial will comprehensively introduce it

 

What is Fiber Optic Circulator? How does a circulator work?

 

Fiber Circulator is a nonreciprocal device that directs an optical signal from one port to the next, in only one direction at a time. While the direction of the optical signal may be redirected as needed, the optical signal must pass through ports sequentially (i.e. from port 1, to port 2, before traveling to port 3). Additionally, it can be used to achieve bi-directional transmission over a single fiber. Because of its high isolation of the input and reflected optical powers and its low insertion loss, it is widely used in advanced communication systems and fiber optic sensor applications.

 

How does Optic Fiber Circulator Work?

 

It operates in a similar way to optical isolator which also uses Faraday rotators, however, its construction is more complex. Its reverse propagating lightwave is directed to a third port for output, instead of being lost. Figure 1(a) shows a three-port optical Fiber circulator. An input signal (λ1) at Port 1 exits at Port 2, an input signal (λ2) at Port 2 exits at Port 3, and an input signal (λ3) at Port 3 exits at Port 1. In the same way, in a four-port  circulator, as shown in Figure 1(b), one could ideally have four inputs and four outputs. In practise, many applications do not need four inputs and four outputs. Therefore, in a four-port circulator, it is common to have three input ports and three output ports. This is done by making Port 1 an input-only port, Port 2 and Port 3 input and output ports, and Port 4 an output-only port.

 

3-port circulator and 4-port circulator

Figure 1. 3-port  Circulator and 4-port Circulator


Types of Circulators

 

According to the number of ports, optic fiber circulators can be usually classified as three types: 3-port, 4-port and 6-port. In general, 3-port and 4-port circulators are quite common, while the 6-port circulators are less commonly used. No matter which port-type of the optical Fiber circulators, optical light is transmitted from any of the port in such circulators can be redirected to any other port.

In addition, optical Fiber circulators can also be classified as two types in the market: Polarization Maintaining (PM) and Polarization Insensitive (PI). PM circulator is manufactured with polarization maintaining fiber, making them ideal for polarization maintaining applications such as 40Gbps systems or Raman pump applications. They are also used in double-pass amplifiers and in Dispersion Compensation Modules (DCMs). PI Fiber circulator is a compact, high-performance lightwave component. This component provides high isolation, low insertion loss, low Polarization Dependent Loss (PDL), and high stability and reliability. It is widely used in combination with fiber gratings and other reflective components in Dense Wavelength Division Multiplexing (DWDM) systems, high speed systems and bi-direction communication systems.

 

Applications of Optical Fiber Circulators

 

Optical fiber circulator supports bi-directional ports and allows a single fiber to be used for both transmission and reception of an optical signal. It is widely used in many applications, such as DWDM networks, polarization mode dispersion, chromatic dispersion compensation, Optical Add-drop Multiplexers (OADMs), optical amplifiers, and fiber optic sensors.

 

DWDM Networks

 

Fibermart circulator can be used to drop an optical channel from a DWDM system using a Fiber Bragg Grating (FBG) (shown in Figure 2). The input DWDM channels are coupled into Port 1 of the device with a FBG device connected to Port 2. The single wavelength reflected from the FBG then reenters the fibermart Circulator in Port 2 and is routed accordingly to Port 3. The remaining signals pass through the FBG and exit on the top fiber.

 

DWDM application 1
Figure 2. Circulator used to drop an optical channel from a DWDM system using a FBG

 

In addition, the optic fiber circulator is also used to separate forward and backward propagating signals with 50 dB of isolation (protection of the input fiber from returning power while employing the rejected light) in DWDM systems. Optic fiber circulator also provides a level of cross-talk (the ratio of the output power produced by the desired input to the output power produced by undesired inputs) of more than 60 dB. This allows a single fiber to effectively transmit a bi-directional signal. (Shown in Figure 3)

 

DWDM application Optical Circulator
Figure 3. Circulator can be used to send optical signals through a single fiber in two directions

 

OADM

 

OADM is based on one FBG and two Fiber circulators. 4 channels, depicted as 4 colours, impinge onto an FBG via an FO circulator. The FBG is set to one of the channels, here Channel 4, which is reflected back to the circulator where it is directed down and "dropped" out of the system. Since the channel has been dropped, another signal on that channel can be "added" at the same point in the network. Shown in Figure 4)

 

circulator-OADM application

Figure 4. FO circulator used in OADM

 

Polarization Mode Dispersion

 

Some fiber optic systems experience polarization mode dispersion (PMD), an inherent property of all optical media. PMD is caused by the difference in the propagation velocities of light in the orthogonal principal polarization states of the transmission medium. If the optical pulse contains both polarization components, then the different polarization components in FO circulators will travel at different speeds and arrive at different times, smearing the received optical signal. With optical couplers, optic circulators can correct PMD by rotating the electric and magnetic field of the optical signal. (Shown in Figure 5)

 

PMD optical circulator

Figure 5. Polarization Mode Dispersion (PMD)

 

 

 

 

 

 

 

 

 

 

 

 

 

Chromatic Dispersion Compensation

 

Optical fiber circulator compensates for chromatic dispersion by using a chipped FBG (wavelength dependent reflector). A section of optical fiber is treated or doped with a material that changes the refractive index of the fiber, causing wavelength dependent reflections. Chipped FBGs have several gratings displaced throughout a fiber and allow for compensation of chromatic dispersion. (Shown in Figure 6)

 

CDM application circulator

Figure 6. Fibermart circulator compensates for chromatic dispersion by using a chipped FBG

Optical Amplifiers


Optical amplifiers create a direct amplification of a signal without needing to convert it into an electrical signal. Fibermart circulators feed the input signal into the amplifier, receive the amplified signal, and reroute the signal to an output port. In this application the circulator supplies suppressed feedback from the cavity. Figure 7 shows this process.

 

amplifier, circulator

Figure 7. Optic Fibermart circulator used in optical amplifier

 

Fiber Optic Sensors

 

Fiber optic sensors are used to measure parameters such as strain, temperature, and pressure. They use optical Fiber circulators to reroute signals. The high isolation between the input and reflected optical power coupled with a low insertion loss make optic fiber circulator the preferred component for interfacing with fiber optic sensors. Figure 8 shows the setup used to calibrate the FBGs with optical circulator.

 

fiber optic sensor application with circulator

Figure 8. Setup used to calibrate the FBGs with FO circulator

Fibre-MART's Optical Circulator Solutions

 

Fiber-Mart offers both PI and PM circulators (working at 1310, 1550, or 1064nm wavelengths) with 3 or 4 ports. Our optic circulators are featured with high isolation, low insertion loss, and excellent environmental stability. In addition, any other wavelengths, without or with any connector can be customized up to customers' requirements.

 


Featured Products
Optical Switches Supply

Optical switches supply from Fiber-Mart

Various Optical Switches Meet Your Different Requirements
SDH Optical Amplifiers

SDH Optical Amplifiers for sales

Booster, In-Line, Pre-Amplifiers for SDH Networks
Optical Attentuators

Optical Attenuator on Fiber-Mart

FC, SC, ST, LC, E2000 Attenuators with APC/UPC Polish Types
Email for Technical Tips
-consulting for technical supports or relevent product buying guide
Email for [email protected]

 






News for Monday 16 March, 2015


View all news for Monday 16 March, 2015 on one page




Recent News




News Archive - See All News from Fiber-Mart.COM


Copyright © 2009-2021 Fiber-MART.COM. All Rights Reserved.
Fiber-MART.COM Secure Certificate
Product Tags: A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z | 0-9