EnglishEspañolFrançaisDeutschPortuguês

fibermart-news_banner_9.jpg

 

Friday 17 August, 2018 | RSS Feed

Common Passive Fiber Optical Splitters

by www.fiber-mart.com

Fiber optical splitter, also named fiber optic coupler or beam splitter, is a device that can distribute the optical signal (or power) from one fiber among two or more fibers. Fiber optic splitter is different from WDM(Wavelength Division Multiplexing) technology. WDM can divide the different wavelength fiber optic light into different channels, but fiber optic splitter divide the light power and send it to different channels.
 
Work Theory Of Optical Splitters
 
The Optical Splitters “split” the input optical signal received by it between two optical outputs, simultaneously, in a pre-specified ratio 90:10 or 80:20. The most common type of fiber-optic splitter splits the output evenly, with half the signal going to one leg of the output and half going to the other. It is possible to get splitters that use a different split ratio, putting a larger amount of the signal to one side of the splitter than the other. Splitters are identified with a number that represents the signal division, such as 50/50 if the split is even, or 80/20 if 80% of the signal goes to one side and only 20% to the other.
 
Some types of the fiber-optic splitter are actually able to work in either direction. This means that if the device is installed in one way, it acts as a splitter and divides the incoming signal into two parts, sending out two separate outputs. If it is installed in reverse, it acts as a coupler, taking two incoming signals and combing them into a single output. Not every fiber-optic splitter can be used this way, but those that can are labeled as reversible or as coupler/splitters.
 
Attenuation Of Fiber Optic Splitter
 
An interesting fact is that attenuation of light through an optical splitter is symmetrical. It is identical in both directions. Whether a splitter is combining light in the upstream direction or dividing light in the downstream direction, it still introduces the same attenuation to an optical input signal (a little more than 3 dB for each 1:2 split). Fiber optic splitters attenuate the signal much more than a fiber optic connector or splice because the input signal is divided among the output ports. For example, with a 1 X 2 fiber optic coupler, each output is less than one-half the power of the input signal (over a 3 dB loss).
 
Passive And Active Splitters
 
Fiber optic splitters can be divided into active and passive devices. The difference between active and passive couplers is that a passive coupler redistributes the optical signal without optical-to-electrical conversion. Active couplers are electronic devices that split or combine the signal electrically and use fiber optic detectors and sources for input and output.
 
Passive splitters play an important position in Fiber to the Home (FTTH) networks by permitting a single PON (Passive Optical Network) network interface to be shared amongst many subscribers. Splitters include no electronics and use no power. They’re the community parts that put the passive in Passive Optical Network and are available in a wide range of break up ratios, including 1:8, 1:16, and 1:32.
 
Optical splitters are available in configurations from 1×2 to 1×64, such as 1:8, 1:16, and 1:32. There are two basic technologies for building passive optical network splitters: Fused Biconical Taper (FBT) and Planar Lightwave Circuit (PLC). FBT Coupler is the older technology and generally introduces more loss than the newer PLC Splitter.





Other news for Friday 17 August, 2018


View all news for Friday 17 August, 2018 on one page




News for Thursday 16 August, 2018


View all news for Thursday 16 August, 2018 on one page




Recent News




News Archive - See All News from Fiber-Mart.COM


Copyright © 2009-2021 Fiber-MART.COM. All Rights Reserved.
Fiber-MART.COM Secure Certificate
Product Tags: A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z | 0-9