1M Simplex LC/APC 9/125 Singlemode Fiber Optic Pigtail 0.9mm PVC Jacket Fast delivery and service are completely satisfying!
3 of 5 Stars!
2M Simplex E2000/APC 9/125 Singlemode Fiber Optic Pigtail 0.9mm PVC Jacket Quality of the products perfectly!
4 of 5 Stars!
2M LC UPC to LC UPC Duplex 3.0mm PVC(OFNR) 10G OM4 Uniboot Fiber Patch Cable Very satisfied with the Customer Service, prompt responses...
5 of 5 Stars!
12fiber 3.0mm 9/125 Singlemode LC/SC/ST/FC Armored Bunch Fiber Optic Pigtail The cable didn't disappoints me, will back again.
3 of 5 Stars!
SM 9/125 Duplex Fiber Patch Cable FTTH Indoor Cable FRP G652D PVC Matches very well,will re-order again.
3 of 5 Stars!
10M LC UPC to SC UPC Simplex 2.0mm LSZH SMF Bend Insensitive Fiber Patch Cable The fast delivery and service are completely satisfying.
4 of 5 Stars!
IP67 LC to IP67 LC Duplex Single mode Waterproof Fiber Optic Patch Cable The order was shipped promptly, and the customer service is...
5 of 5 Stars!
FC/APC to MU/UPC Duplex Singlemode 9/125 Armored Patch Cable Nice price and easy to use, no prombles. Works fine. Sue...
5 of 5 Stars!
1M Simplex LC/APC 9/125 Singlemode Fiber Optic Pigtail 0.9mm PVC Jacket Fast delivery and service are completely satisfying!
3 of 5 Stars!
2M Simplex E2000/APC 9/125 Singlemode Fiber Optic Pigtail 0.9mm PVC Jacket Quality of the products perfectly!
4 of 5 Stars!
2M LC UPC to LC UPC Duplex 3.0mm PVC(OFNR) 10G OM4 Uniboot Fiber Patch Cable Very satisfied with the Customer Service, prompt responses...
5 of 5 Stars!
12fiber 3.0mm 9/125 Singlemode LC/SC/ST/FC Armored Bunch Fiber Optic Pigtail The cable didn't disappoints me, will back again.
3 of 5 Stars!
SM 9/125 Duplex Fiber Patch Cable FTTH Indoor Cable FRP G652D PVC Matches very well,will re-order again.
3 of 5 Stars!
10M LC UPC to SC UPC Simplex 2.0mm LSZH SMF Bend Insensitive Fiber Patch Cable The fast delivery and service are completely satisfying.
4 of 5 Stars!
IP67 LC to IP67 LC Duplex Single mode Waterproof Fiber Optic Patch Cable The order was shipped promptly, and the customer service is...
5 of 5 Stars!
FC/APC to MU/UPC Duplex Singlemode 9/125 Armored Patch Cable Nice price and easy to use, no prombles. Works fine. Sue...
5 of 5 Stars!
Quick Re-Order

fibermart-news_banner_9.jpg

 

Wednesday 12 December, 2018 | RSS Feed

Introduction of Fiber Optic Cleaving

by www.fiber-mart.com

As we know, in most cases, when a fiber is used or spliced, it is essential to prepare clean ends. Stripping, cleaving, polishing are the basic steps to ensure fiber ends clean and smooth. Since we have discussed fiber optic splicing and polishing in the last several weeks, we must know more about them. Cleaving, an essential step of making fiber ends clean, though it’s a simple mean, but it works surprisingly well, at least for standard glass fibers. Thus, I want to share something about the cleaving in this paper today.
 
Understanding Of Cleaving
 
Cleaving is one of the processes for termination or splicing. Simple to understand, it “cut” an optical fiber or makes it precisely broken, just like cutting glass plate. But it is different from the general concept “cut”, or perhaps, we may define it as a professional “cut technique” because fiber is cut by scoring or scratching the surface and applying stress so that the glass breaks in a smooth manner along the stress lines created by the scratch. With a properly well done cleaving, the fiber will cleave with a clean surface perpendicular to the length of the fiber, with no protruding glass on either end.
 
Cleaver – If you have more experiences in the cleaving and splicing, you must know that a right cleaver helps cut out costly mistakes. The working principle of cleaver is very easy to understand. It first holds the fiber under low tension, scores the surface at the proper location and then applies greater tension until the fiber breaks. Automatic cleavers now are widely used because they can produce consistent results, irrespective of the operator. It is easy to use and does not need training. Users just need to clamp the fiber into the cleaver and operate its controls. In addition, there are some cleavers less automated. This kind of cleavers are more dependent on operator technique and less predictable as they require operators to exert force manually for breaking the fiber.
 
Scribe – Except the cleaver, there is another tool for cleaving which is typically used to remove excess fiber from the end of a connector before polishing. Scribe is a simple hand tool with a hard, sharp tip (generally made of carbide or diamond), that is used to scratch the fiber manually (some scribes are with pen-style shapes). Then the operator pulls the fiber to break it. However, it is less predictable than a cleaver because both the scribing and breaking process are under manual control. Nonetheless, scribe can produce adequate results for polishing so that it is still used today.
 
Why Is Proper Cleaving So Important?
 
To get good fiber optic splices or terminations, especially when using the pre-polished connectors with internal splices, it is extremely important to cleave the fiber properly. As we know, fiber splicing requires mating two fiber ends. Any defect of the ends would impact the performance of fiber splicing. For example, if the fiber ends are not precisely cleaved, the ends will not mate properly. Or if the cleaved ends are at an angle, there will be a gap between the fibers that will cause loss in a mechanical splice or uneven fusion splicing. In addition, if there is a protrusion, or lip, on one of the fibers, the two fibers will not butt up against each other and if there are hackle or mist, the ends will reflect or diffuse light, also causing loss.
 
Warm Tips: A good cleaver is a little expensive but it’s easy to use and do not need much techniques and can help cut out costly mistakes. Of course, inexpensive cleaver provided in most termination kits is common used. If you decide to use such inexpensive cleaver, the point you may remember is that you must learn how to use it properly. Follow directions, but also do what comes naturally to you when using the device, as they are sensitive to individual technique.





Other news for Wednesday 12 December, 2018


View all news for Wednesday 12 December, 2018 on one page




News for Tuesday 11 December, 2018


View all news for Tuesday 11 December, 2018 on one page




Recent News




News Archive - See All News from Fiber-Mart.COM


Newsletter
Enter your email for new arrivals, brands and special offers!
Tags: High Power Splitter | HT 312S Cable Strippers | HT 312B Coaxial Strippers | High Precision Cleaver | High Power Combiner | High Power Isolator HPIS | HP AJ718A | High Speed meter | High Power Combiners | HP SFP | HP J8177B X121 | HT 1041 | High Power Fiber Amplifier | High Power Polarization Maintaining | High Power Connector | HT 312X | HP Compatible | High Precision Connector | High Power Isolator | HP AJ716A |
Product Tags: A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z | 0-9