EnglishEspañolFrançaisDeutschPortuguês日本語한국인
Blog Filter
Solutions
See more
See less
Product
See more
See less
Recent Order

The FOA Reference For Fiber Optics

  • The FOA Reference For Fiber Optics Fiber-Mart.com
  • Post on Sunday 24 September, 2017
  • 792
  • 0

Fiber optic transmission systems (datalinks) all work similar to the diagram shown above. They consist of a transmitter on one end of a fiber and a receiver on the other end.


Fiber Optic Transmitters and Receivers (Transceivers)
 
Fiber optic transmission systems (datalinks) all work similar to the diagram shown above. They consist of a transmitter on one end of a fiber and a receiver on the other end. Most systems operate by transmitting in one direction on one fiber and in the reverse direction on another fiber for full duplex operation.
 
Most systems use a "transceiver" which includes both transmission and receiver in a single module. The transmitter takes an electrical input and converts it to an optical output from a laser diode or LED. The light from the transmitter is coupled into the fiber with a connector and is transmitted through the fiber optic cable plant. The light from the end of the fiber is coupled to a receiver where a detector converts the light into an electrical signal which is then conditioned properly for use by the receiving equipment.
 
The sources used for fiber optic transmitters need to meet several criteria: it has to be at the correct wavelength, be able to be modulated fast enough to transmit data and be efficiently coupled into fiber.
CWDM SFP+ 20km Transceiver
Four types of sources are commonly used, LEDs, fabry-perot (FP) lasers, distributed feedback (DFB) lasers and vertical cavity surface-emitting lasers (VCSELs). All convert electrical signals into optical signals, but are otherwise quite different devices. All three are tiny semiconductor devices (chips). LEDs and VCSELs are fabricated on semiconductor wafers such that they emit light from the surface of the chip, while f-p lasers emit from the side of the chip from a laser cavity created in the middle of the chip. 
 
LEDs have much lower power outputs than lasers and their larger, diverging light output pattern makes them harder to couple into fibers, limiting them to use with multimode fibers. Laser have smaller tighter light outputs and are easily coupled to singlemode fibers, making them ideal for long distance high speed links. LEDs have much less bandwidth than lasers and are limited to systems operating up to about 250 MHz or around 200 Mb/s. Lasers have very high bandwidth capability, most being useful to well over 10 GHz or 10 Gb/s.

 Because of their fabrication methods, LEDs and VCSELs are cheap to make. Lasers are more expensive because creating the laser cavity inside the device is more difficult, the chip must be separated from the semiconductor wafer and each end coated before the laser can even be tested to see if its good.
10G XENPAK to SFP+ Converter Module
LEDs have a limited bandwidth while all types of lasers are very fast. Another big difference between LEDs and both types of lasers is the spectral output. LEDs have a very broad spectral output which causes them to suffer chromatic dispersion in fiber, while lasers have a narrow spectral output that suffers very little chromatic dispersion. DFB lasers, which are used in long distance and DWDM systems, have the narrowest spectral width which minimizes chromatic dispersion on the longest links. DFB lasers are also highly linear (that is the light output directly follows the electrical input) so they can be used as sources in AM CATV systems.
 
The choice of these devices is determined mainly by speed and fiber compatibility issues.  As many premises systems using multimode fiber have exceeded bit rates of 1 Gb/s, lasers (mostly VCSELs) have replaced LEDs. The output of the LED is very broad but lasers are very focused, and the sources will have very different modal fill in the fibers. The restricted launch of the VCSEL (or any laser) makes the effective bandwidth of the fiber higher, but laser-optimized fiber, usually OM3, is the choice for lasers.
 
The electronics for a transmitter are simple. They convert an incoming pulse (voltage) into a precise current pulse to drive the source. Lasers generally are biased with a low DC current and modulated above that bias current to maximize speed.
 
Detectors for Fiber Optic Receivers
 
Receivers use semiconductor detectors (photodiodes or photodetectors) to convert optical signals to electrical signals. Silicon photodiodes are used for short wavelength links (650 for POF and 850 for glass MM fiber). Long wavelength systems usually use InGaAs (indium gallium arsenide) detectors as they have lower noise than germanium which allows for more sensitive receivers.
 
Packaging

Transcivers are usually packaged in industry standard packages like these XFP modules for gigabit datalinks(L) and Xenpak (R). The XFP modules connect to a duplex LC connector on the optical end and a standard electrical interface on the other end. The Xenpak are for 10 gigabit networks but use SC duplex connection. Both are similar to media converters but are powered from the equipment they are built into.
 
Performance

Just as with copper wire or radio transmission, the performance of the fiber optic data link can be determined by how well the reconverted electrical signal out of the receiver matches the input to the transmitter. The discussion of performance on datalinks applies directly to transceivers which supply the optical to electrical conversion.

Every manufacturer of transceivers specifies their product for receiver sensitivity (perhaps a minimum power required) and minimum power coupled into the fiber from the source. Those specifications will end up being the datalink specifications on the final product used in the field.

All datalinks are limited by the power budget of the link. The power budget is the difference between the output power of the transmitter and the input power requirements of the receiver. The receiver has an operating range determined by the signal-to-noise ratio (S/N) in the receiver. The S/N ratio is generally quoted for analog links while the bit-error-rate (BER) is used for digital links. BER is practically an inverse function of S/N.
 
 
 
Comments: (0)

No comments have been posted yet.

Leave a Comment
You must be logged in to submit a comment.
Copyright © 2009-2024 Fiber-MART.COM All Rights Reserved. Privacy Notice. Terms of Service
Fibermart ISO9001Fibermart Secure Certificate
Product Tags: A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z | 0-9
Email us